BepiColombo (MPO+MMO) - Ariane 5 ECA (VA245) - Kourou ELA-3 - 20.10.2018 - 04:45:35 ДМВ

Автор Карлсон, 27.02.2007 21:42:10

« назад - далее »

0 Пользователи и 2 гостей просматривают эту тему.

instml

http://forum.nasaspaceflight.com/index.php?topic=6845.msg928171#msg928171

BepiColombo Composite Spacecraft Mass Properties Measurements

10 Jul 2012 15:51

The mass properties of the BepiColombo Mercury Composite Spacecraft have been measured. This is the first time that the spacecraft structural and thermal model has been fully integrated, producing the configuration in which it will be launched and effect the transfer to Mercury.



http://sci.esa.int/science-e/www/object/index.cfm?fobjectid=50552
Go MSL!

instml

ВИДЕО

Good vibrations for BepiColombo
 
17 August 2012
ЦитироватьMimicking the intense vibrations experienced by a satellite during launch, the engineering model of the BepiColombo mission to Mercury has been subjected to similar forces at ESA's spacecraft test facilities.

A major design issue for spacecraft arises from the intense environment experienced during launch, ranging from vigorous vibrations to deafening noise. It is essential to test spacecraft under similar conditions here on Earth, to ensure they will survive the violent ride to space.

In these videos of recent vibration tests, the BepiColombo structural and thermal model is in its launch configuration in the test facilities at ESTEC, ESA's technical centre in Noordwijk, the Netherlands.

BepiColombo is a joint mission between ESA and the Japan Aerospace Exploration Agency to explore the properties of Mercury, the enigmatic innermost planet in our Solar System.

The spacecraft comprises a number of components. Seen here from top to bottom are the sunshield, which conceals the Japanese Mercury Magnetospheric Orbiter, with the European Mercury Planetary Orbiter below. Underneath is the Mercury Transfer Module, which will deliver the two scientific satellites into orbit around the planet.  

During the tests the spacecraft was mounted on a table where it was shaken up-and-down or from side-to-side to mimic the vibrations it will experience when it lifts off on an Ariane 5 launch vehicle in 2015.

Each test lasted for 2.5 minutes during which the frequency of the vibrations was increased from 3 Hz to 100 Hz. At the lowest frequencies the spacecraft movement reached 10 cm, which decreased as the frequency continued to rise.

Other mechanical tests to simulate the launch and voyage in space include exposing the spacecraft to the tremendous noise a rocket produces, the harsh vacuum of space, and scorching temperatures of some 450°C that the modules will endure as they orbit around the closest planet to the Sun.

The engineering model will also be subjected to the shocks generated during the separation of BepiColombo from the launcher, the separation of the individual spacecraft modules and the deployment of its solar arrays and antennas.

BepiColombo is scheduled to launch in 2015 and will arrive at Mercury in 2022. The two orbiters will study the planet's composition, geophysics, atmosphere, magnetosphere, and geological history.

As the nearest planet to the Sun, Mercury has an important role in the story of planet formation. Mercury together with Venus and Mars make up Earth's rocky neighbourhood. Each planet holds information necessary for understanding how the innermost planets of our Solar System formed and evolved.
http://www.esa.int/esaSC/SEMSTQYXP5H_index_0.html
Go MSL!

Salo

http://www.esa.int/esaSC/SEM4IA4Y96H_index_0.html
ЦитироватьThe shock of separation[/size]
 
27 August 2012  

 Simulating separation shock  
 
The BepiColombo mission to Mercury has undergone a series of shock tests at ESA's test facilities to replicate conditions it will experience during its intense ride into space. This video shows tests to mimic the moment it separates from the launch vehicle.

 The spacecraft will be connected to the upper stage of an Ariane 5 rocket when it blasts off from Earth in 2015. Once the upper stage and its cargo have reached orbit, the pair will separate.

 This is achieved via a pyrotechnic device that will fire open a clamp band, allowing springs to push the spacecraft safely away from the upper stage.

 The firing of the pyrotechnic device causes a mechanical shock that transmits through the spacecraft.

 To ensure the components of BepiColombo will survive these shocks, and others that occur at fairing opening, rigorous assessments are being carried out at the spacecraft test facilities at ESTEC, ESA's technical centre in Noordwijk, the Netherlands.

 To simulate the launch vehicle separation, the spacecraft structural and thermal test model was suspended from an overhead crane above blocks of foam rubber.

 Compressed gas, rather than a pyrotechnic device, opened the clamp and the launch vehicle assembly unit dropped onto the cushioned surface.

 At the same time, a number of accelerometers mounted on the spacecraft measured the effect of the shock.

 Other mechanical tests to simulate the launch and voyage in space include exposing the spacecraft to the tremendous noise a rocket produces, the harsh vacuum of space, and scorching temperatures of some 450°C that the modules will endure as they orbit around the closest planet to the Sun.

 BepiColombo is an international mission between ESA and the Japanese Space Agency, JAXA. It is scheduled for launch in 2015 and will arrive at Mercury in 2022.

 The spacecraft comprises two scientific satellites, Japan's Mercury Magnetospheric Orbiter and Europe's Mercury Planetary Orbiter.

 A third component, the Mercury Transfer Module, will deliver the two satellites into orbit around the planet, where they will study the planet's composition, geophysics, atmosphere, magnetosphere and geological history.[/size]
По ссылке есть видео.
"Были когда-то и мы рысаками!!!"

instml

http://www.unmannedspaceflight.com/index.php?showtopic=1753&view=findpost&p=191208
http://sci.esa.int/science-e/www/object/index.cfm?fobjectid=47346

ЦитироватьKey mission dates

Date Mission event
15 August 2015 Launch
14 August 2016 Earth flyby
25 November 2017 First Venus flyby
18 July 2018 Second Venus flyby
15 February 2019 First Mercury flyby
07 November 2019 Second Mercury flyby
26 January 2021 Third Mercury flyby
08 March 2021 Fourth Mercury flyby
27 January 2022 Arrival at Mercury
27 April 2023 End of nominal mission
27 April 2024 End of extended mission

Торможение (или разгон?) ионниками и семь гравитационных маневров. Жесть короче :D
Go MSL!

Имxотеп

ЦитироватьТорможение (или разгон?) ионниками и семь гравитационных маневров. Жесть короче :D

Кстати говоря, до переноса на 2015й план полета выглядел следующим образом:

Старт с Земли- 19.07.2014
Пролет Земли - 26.07.2015
1й пролет Венеры - 18.01.2016
2й пролет Венеры - 29.08.2016
1й пролет Меркурия - 05.09.2017
2й пролет Меркурия - 27.05.2018
3й пролет Меркурия - 17.08.2019
4й пролет Меркурия - 27.09.2019
Выход на орбиту вокруг Меркурия - 13.11.2020

В принципе это схема, опробованная MESSENGER'ом. Выход на орбиту, близкую к орбите Земли, встреча с ней примерно через год после старта, перелет к орбите Венеры. Затем, чтобы дотянуться до орбиты Меркурия, 2 пролета Венеры, обычно они разделены одним венерианским годом. И наконец несколько пролетов Меркурия на резонансных орбитах. Единственное отличие от MESSENGER'a состоит разве в том, что все большие коррекции теперь размазаны вдоль орбиты длинными дугами работы ионников. Ну и собственно итоговый подход к сфере действия Меркурия, последние 1.8 км/с, тоже на ионниках.
Итого - 5.5 лет в пути, 4 км/с ХС собственными силами.

Однако теперь пуск перенесли на год и вся красота рассыпалась. Венера ушла из точки встречи, поэтому ее первый пролет состоится не через 6 месяцев после пролета Земли, а через 15. С Меркурием попроще, но тоже лезут всякие побочные неоптимальности.
Итого - 6.5 лет в пути + год отсрочки, ХС примерно та же.

ЗЫ А будь у них Атлас 5 (551), можно было бы весь колхоз отправить сразу к Венере и сэкономить тем 2 года полета.  :D

Bizonich

Цитироватьhttp://www.unmannedspaceflight.com/index.php?showtopic=1753&view=findpost&p=191208
http://sci.esa.int/science-e/www/object/index.cfm?fobjectid=47346

ЦитироватьKey mission dates

Date Mission event
15 August 2015 Launch
14 August 2016 Earth flyby
25 November 2017 First Venus flyby
18 July 2018 Second Venus flyby
15 February 2019 First Mercury flyby
07 November 2019 Second Mercury flyby
26 January 2021 Third Mercury flyby
08 March 2021 Fourth Mercury flyby
27 January 2022 Arrival at Mercury
27 April 2023 End of nominal mission
27 April 2024 End of extended mission

Торможение (или разгон?) ионниками и семь гравитационных маневров. Жесть короче :D
Это даже не жесть, это я даже не знаю как назвать.  :shock: Мессенджер 7 лет летел. А он вообще 9.
Любознательный дилетант.

smokan

Цитировать
Цитироватьhttp://www.unmannedspaceflight.com/index.php?showtopic=1753&view=findpost&p=191208
http://sci.esa.int/science-e/www/object/index.cfm?fobjectid=47346

ЦитироватьKey mission dates

Date Mission event
15 August 2015 Launch
14 August 2016 Earth flyby
25 November 2017 First Venus flyby
18 July 2018 Second Venus flyby
15 February 2019 First Mercury flyby
07 November 2019 Second Mercury flyby
26 January 2021 Third Mercury flyby
08 March 2021 Fourth Mercury flyby
27 January 2022 Arrival at Mercury
27 April 2023 End of nominal mission
27 April 2024 End of extended mission

Торможение (или разгон?) ионниками и семь гравитационных маневров. Жесть короче :D
Это даже не жесть, это я даже не знаю как назвать.  :shock: Мессенджер 7 лет летел. А он вообще 9.

Как 9? Не 9, а 6,5, смотрите где Arrival at Mercury

Bizonich

ЦитироватьКак 9? Не 9, а 6,5, смотрите где Arrival at Mercury
Точно, спасибо, не посмотрел. Значит нормально.
Любознательный дилетант.

Salo

http://www.spacenews.com/article/thales-alenia-space-to-build-bepicolombo-components#.UMJBJ6y3mHA
ЦитироватьThales Alenia Space To Build BepiColombo Components
Dec. 7, 2012

ESA's BepiColombo. Credit: Thales Alenia artist's concept

PARIS — Thales Alenia Space Italy has signed a contract valued at 200 million euros ($260 million) with Astrium GmbH of Germany to provide telecommunications, thermal control and electric-power systems for Europe's $1 billion BepiColombo Mercury orbiter, Thales Alenia Space announced Dec. 5.

The contract comes five years after the two companies signed an original authorization to proceed that allowed hardware design to begin.

BepiColombo, whose budget and schedule have slipped on several occasions as the satellite grew in weight, forcing a launch aboard a heavy-lift Ariane 5 instead of a medium-lift Soyuz rocket, is currently scheduled for launch in 2015.

The European Space Agency (ESA) is managing BepiColombo in cooperation with Japan's JAXA space agency. ESA's work includes the Astrium- and Thales Alenia Space-built Mercury Planetary Orbiter. JAXA is providing the Mercury Magnetospheric Orbiter.

Both orbiters will be launched aboard the same Ariane 5 vehicle on a 6.5-year journey to Mercury orbit attached to the Mercury Transfer Module. Once in Mercury orbit, the two satellites will separate.

The satellites are scheduled to operate for a year at Mercury to investigate the origins and evolution of the planet, with a possible one-year extension. One of the principal design challenges is to withstand the temperature extremes in Mercury orbit, as high as 350 degrees Celsius on the side facing the sun.
"Были когда-то и мы рысаками!!!"

pkl

А "Кассини" к Сатурну 7. А ведь Меркурий я время от времени вижу на закате. :oops:
Вообще, исследовать солнечную систему автоматами - это примерно то же самое, что посылать робота вместо себя в фитнес, качаться.Зомби. Просто Зомби (с)
Многоразовость - это бяка (с) Дмитрий Инфан

Молодой

Цитироватьpkl пишет:
А "Кассини" к Сатурну 7. А ведь Меркурий я время от времени вижу на закате.  :oops:
Интересно, какой двигатель нужен для прямого полета к Меркурию, чтоб погасить эти 30 км/с, ЯРД  или плазменный РД сойдут?
Наша реальность-научная фантастика давно минувших эпох...

ZOOR

http://www.iki.rssi.ru/annual/2012/R32_OKR_NIR-12.pdf
ЦитироватьПроект МСП-2001
 
В рамках ОКР по теме МСП-2001 Федерального космического агентства ведутся опытно-конструкторские разработки аппаратуры для экспериментов:  
- проект «Меркурианский нейтронный и гамма спектрометр» (МГНС) для орбитального КА ЕКА «Бепи Коломбо» (БК, срок запуска – II-е полугодие 2014 года).
-  прибор МГНС.  Все работы выполнены в соответствии с Техническим заданием на ОКР по теме.

Руководитель проекта: Д.ф.м.н. Митрофанов И.Г. тел.: (495) 333-3489, imitrofa@space.ru
Я зуб даю за то что в первом пуске Ангары с Восточного полетит ГВМ Пингвина. © Старый
Если болит сердце за народные деньги - можно пойти в депутаты. © Neru - Старому

PIN

ЦитироватьZOOR пишет:
 http://www.iki.rssi.ru/annual/2012/R32_OKR_NIR-12.pdf 
Цитировать- прибор МГНС. Все работы выполнены в соответствии с Техническим заданием на ОКР по теме.


Насколько помню, этим летом или в сентябре уже проводились (успешно) интеграционные тесты МГНС в Фридрихсхафене, приезжали двое ребят из команды Митрофанова

Salo

http://www.esa.int/Our_Activities/Technology/How_to_cook_a_spacecraft
ЦитироватьHow to cook a spacecraft
27 February 2013

The faint aroma of hot metal filled the surrounding cleanroom as the hatch to ESA's newest test facility was slid aside, concluding a 23-day 'bake-out' of the largest segment of ESA's mission to Mercury.

Ending on the early hours of 14 February, this test ensured ESA's Mercury Planetary Orbiter – MPO, part of the multi-module BepiColombo mission – was cleaned of potential contaminants in advance of its 2015 mission to the inner Solar System.

The bake-out took place at ESA's technical heart, ESTEC in Noordwijk, the Netherlands, which includes a dedicated Test Centre equipped to simulate all aspects of the space environment.

MPO will fly to the innermost planet with Japan's Mercury Magnetosphere Orbiter, riding together on ESA's propulsion module. But not before getting cooked first.

"Being close to Mercury and experiencing high temperatures, the release of molecules fr om spacecraft materials is expected to occur at higher quantities than for normal satellites," explains Jan van Casteren, BepiColombo Project Manager.

"Such molecules are a contamination threat if they condense on sensitive surfaces, so we need to minimise outgassing in order to protect our delicate scientific instrumentation on the spacecraft."

So an initial bake-out of the various spacecraft segments is essential for cleaning purposes – in this case MPO's 'Proto-Flight Model', incorporating its propulsion system and heat pipes that regulate its temperature.

A new test facility called Phenix hosted the bake-out, a 4.5 m-diameter stainless steel vacuum chamber 11.8 m long, with an inner box called the 'thermal tent' whose six copper walls can be heated up to 100°C or cooled via piped liquid nitrogen down to –190°C, all independent from each other.

"This test was different from more typical thermal vacuum testing because, while the sides and top of the chamber were kept heated to around 50°C, the underside remained cooled by liquid nitrogen throughout," explains Mark Wagner, Head of ESTEC's Test Facilities & Test Methods Section.

"This creates a 'cold trap' wh ere the contaminants baked off from the satellite solidify for collection. But sustaining this environment required 1500 litres of liquid nitrogen per hour – on average three tankers were calling at ESTEC daily to top up our supply."

The test was monitored 24 hours per day on a triple shift system, with care being taken to maintain the temperatures precisely and ensure a continuous flow of data.

Outgassing production was monitored throughout the test, and the bake-out results are now being analysed. A non-trivial amount of contaminants are expected to have been produced – 'spoonfuls' of material.

Now Phenix itself is being thoroughly cleaned, ready for its next customer.
BepiColombo MPO inside Phenix

"Phenix was put in place to extend the range of thermal vacuum test services on offer to ESTEC Test Centre customers," explains Mark. "It is able to accommodate large subsystems or entire spacecraft."

Phenix was cleared for use last December, after which preparations began immediately for BepiColombo testing.

"The chamber will be kept busy for much of the rest of this year accommodating a forthcoming batch of Galileo satellites," Mark concludes.

"This will be more traditional testing – simulating the temperature extremes the Galileo satellites must endure throughout their 12-year working lifetimes."


Mercury Planetary Orbiter being placed in Phenix thermal vacuum facility


BepiColombo MPO inside Phenix
"Были когда-то и мы рысаками!!!"

Salo

http://www.esa.int/Our_Activities/Space_Science/The_mercury_rises_for_BepiColombo
ЦитироватьThe Mercury rises for BepiColombo

 11 March 2013

The engineering model of the BepiColombo Mercury Transfer Module has completed a 12-day Sun-simulation test inside the Large Space Simulator at ESA's test centre in the Netherlands, where it received a taste of the extreme solar heating it will experience when it enters orbit around the Solar System's innermost planet in 2022.

The image was taken during a dry run on 20 February, during which the facility's motion system replicated the different orientations of the simulated solar beam and the positions of the test table.

The real test, in vacuum, began on 26 February and continued non-stop for 12 days. During this time the module was subjected to ten times the solar heating experienced by satellites circling Earth.

Some of the 121 hexagonal mirror segments that direct the simulated solar radiation onto the spacecraft are visible towards the top of the image. The aperture through which the 'sunlight' travels fr om the nineteen 25 kW lamps can be seen just to the left of the mirror segments.

The Mercury Transfer Module will carry the mission's two scientific satellites – Japan's Mercury Magnetospheric Orbiter and Europe's Mercury Planetary Orbiter – into orbit around Mercury. The spacecraft will use electric propulsion to reach its destination.

In this view, one of four ion propulsion engines has already been installed (the grey cylinder close to the centre of the unit), while part of the solar array drive protrudes from the right side of the module.

Earlier this month, the mission's Mercury Planetary Orbiter Mechanical and Propulsion Bus Proto-Flight Model completed a 'bake out' in the Phenix thermal vacuum facility at ESA's ESTEC test facility. This heated the unit to 60°C in a vacuum for 23 days to remove any contaminants that would outgas in space.

BepiColombo is an international mission between ESA and the Japan's JAXA space agency. It is scheduled for launch in 2015 and will arrive at Mercury in 2022, wh ere it will study the planet's composition, geophysics, atmosphere, magnetosphere and geological history.


BepiColombo module in space simulator
"Были когда-то и мы рысаками!!!"

pkl

ЦитироватьМолодой пишет:
Цитироватьpkl пишет:
А "Кассини" к Сатурну 7. А ведь Меркурий я время от времени вижу на закате.  :oops:  
Интересно, какой двигатель нужен для прямого полета к Меркурию, чтоб погасить эти 30 км/с, ЯРД или плазменный РД сойдут?
Честно говоря, с трудом себе представляю такой двигатель. Мегаваттный ионник? Солнечный парус? :oops:
Вообще, исследовать солнечную систему автоматами - это примерно то же самое, что посылать робота вместо себя в фитнес, качаться.Зомби. Просто Зомби (с)
Многоразовость - это бяка (с) Дмитрий Инфан

ZOOR

#76
http://www.iki.rssi.ru/annual/2013/R32_OKR_NIR-13.pdf
Цитировать2.2 Спектрометрические приборы с российским участием в проекте ESA и JAXA «Бепи Коломбо»

По проекту «Бепи Коломбо» в текущем году продолжалась работа с летными образцами следующих спектрометрических приборов для изучения поверхности и экзосферы Меркурия. Натриевая камера МСАСИ, разрабатываемая в кооперации Японии и России для японского аппарата ММО и ультрафиолетовый спектрометр Фебус, разрабатываемый в кооперации с Франции, России и Японии для европейского аппарата МРО. Запуск КА планируется в 2016 году ракетой Ариан 5 с европейского космодрома в Куру.
Планируемое время полета до Меркурия 6 лет.
Руководитель: д. ф.-м. н. Кораблев О.И., korab@iki.rssi.ru, Котцов В.А., vladkott@mail.ru
и бОлее оптимистичный прогноз
ЦитироватьПроект МСП-2001

В рамках ОКР по теме МСП-2001 Федерального космического агентства ведутся опытно-конструкторские разработки аппаратуры для экспериментов:
проект «Меркурианский нейтронный и гамма спектрометр» (МГНС) для орбитального КА ЕКА «Бепи Коломбо» (БК, срок запуска – II-е полугодие 2014 года).
прибор МГНС. Все работы выполнены в соответствии с Техническим заданием на ОКР по теме.
Руководитель проекта:
Д.ф.м.н. Митрофанов И.Г. тел.: (495) 333-3489, imitrofa@space.ru

Наверное, они на разных Коломбах полетят :(
Я зуб даю за то что в первом пуске Ангары с Восточного полетит ГВМ Пингвина. © Старый
Если болит сердце за народные деньги - можно пойти в депутаты. © Neru - Старому

Andrey Samoilov

#77
Летом 2013 года сообщали, что запуск состоится в 2015-м. Сейчас смотрю - тихой сапой перенесли на год позже.
LAUNCH : 07/2016
 ARRIVAL AROUND MERCURY: 01/2023

Пел Лин

ЦитироватьМолодой пишет:
Цитироватьpkl пишет:
А "Кассини" к Сатурну 7. А ведь Меркурий я время от времени вижу на закате.  :oops:  
Интересно, какой двигатель нужен для прямого полета к Меркурию, чтоб погасить эти 30 км/с, ЯРД или плазменный РД сойдут?
А зачем 30? Это на  Солнце чтобы упасть нужно 30км/сек.  А до Меркурия долететь, если без раскручивающийся  спирали  от земной орбиты, хватит ХС около 9 км/сек

Quoondо

Я так понимаю проект вообще отменили? - очень жаль. Много читал про его мутарства в инете. Жаль что каждый год переносили-переносили и в результате совсем отменили. Меркурию и Венере полюбому не хватает новой АМС. Может индусы с китайцами подстрахуют.. :?: